Renesas PC7501 Manual do Utilizador

PC7501Emulator for M16C FamilyUser’s ManualRev.3.00 June 1, 2004 REJ10J0078-0300T

10 / 46 IMPORTANT Note for Installation: • The emulator PC7501 does not operate stand-alone. It must always be connected with the emulation probe

11 / 46 IMPORTANT Note for LPT Parallel Interface: • With the LPT parallel interface of the PC7501, not all host machines will work and are guaran

12 / 46 MEMO

13 / 46 Chapter 2 PC7501 System Configuration 2.1 Packing List This product's packing list is shown below. • Emulator main unit PC7501 • AC

14 / 46 2.3 PC7501 System Configuration 2.3.1 Host Machine The PC7501 system uses a personal computer (IBM PC/AT or compatible) as a host machine to

15 / 46 2.4 Specifications Table 2.1 lists the specifications of the emulator PC7501. Table 2.1 Specifications Supported MCUs M16C Family (32/16-b

16 / 46 MEMO

17 / 46 Chapter 3 External View 3.1 Names and Functions of Parts on the Upper Panel Figure 3.1 shows the name and function of each switch and indic

18 / 46 3.1.1 System Status LEDs The system status LEDs indicate the emulator PC7501's power supply, firmware operating status, etc. Table 3.1 l

19 / 46 IMPORTANT Note for Using Memory Expansion and Microprocessor Modes: • When using this emulator in memory expansion mode or microprocessor m

Microsoft, MS-DOS, Windows, and Windows NT are registered trademarks of Microsoft Corporation in the U.S. and other countries. IBM and AT are register

20 / 46 3.2.1 Interface Selection Switch The emulator PC7501 allows you to specify one of three types of interfaces for communication with the host m

21 / 46 3.3 Names and Functions of Parts on the Front Panel Figure 3.5 Front panel of the emulator PC7501 3.3.1 System Reset Switch The system re

22 / 46 3.3.2 External Trigger Signal Input/Event Output Connectors For the external trigger signal input/event output connector, insert the external

23 / 46 Chapter 4 Setup This chapter describes how to connect the emulator PC7501 with your host machine and emulation probe M3xxxxTx-EPB. For deta

24 / 46 4.2 Connecting Host Machine When connecting the emulator PC7501 to a host machine, you can choose your desired interface from LPT parallel i

25 / 46 4.2.1 Connecting by LPT Parallel Interface The procedure to set up your system using the LPT parallel interface is shown below. Turn OFF t

26 / 46 Figure 4.2 Connecting the LPT parallel interface cable (host machine side) Figure 4.3 Connecting the LPT parallel interface cable (emulat

27 / 46 4.2.2 Connecting by USB Interface IMPORTANT We do not ensure the operation in every combination with host machine, USB device, and USB hub.

28 / 46 Figure 4.4 Connecting the USB interface cable (host machine side) Figure 4.5 Connecting the USB interface cable (emulator PC7501 side) 10

29 / 46 4.2.3 Connecting by LAN Interface To connect the emulator PC7501 by use of a LAN interface, you need to register some network information suc

3 / 46 Preface The PC7501 system is designed for use with Renesas M16C Family MCUs. The PC7501 system is configured with the emulator PC7501, an emu

30 / 46 IMPORTANT If the LAN interface is used as the PC7501 communication interface, it is necessary to acquire an IP address of the PC7501. For det

31 / 46 IMPORTANT If you have already used IP address 39.40.41.44 in a local area network, you cannot use this procedure. Carry out "(1) Using t

32 / 46 Figure 4.7 Connecting the LAN interface cable (host machine side) Figure 4.8 Connecting the LAN interface cable (emulator PC7501 side) ,

33 / 46 4.3 Connecting Emulation Probe M3xxxxTx-EPB The procedure for connecting the emulation probe to the emulator PC7501 is shown below. Turn OF

34 / 46 4.4 Downloading Firmware 4.4.1 When It is Necessary to Download Firmware It is necessary to download firmware when: (1) You have set up the

35 / 46 4.5 Self-check IMPORTANT The self-check is a function to check the memory and other conditions of the emulator PC7501's internal circui

36 / 46 MEMO

37 / 46 Chapter 5 Troubleshooting 5.1 Emulator PC7501 Cannot Be Powered On □ Is the AC power cable of the PC7501 firmly plugged into the receptacl

38 / 46 5.2.3 LAN Interface □ Was the PC7501 shut off and restarted after the IP address was set? □ Is the interface selection switch on the rear pan

39 / 46 5.3 Firmware Download Error If the power is shut off during the self-check or firmware download for an unexpected reason, it may happen that

4 / 46 Table of Contents Chapter 1 Precautions for Safety 1.1 Safety Symbols and Meanings...

40 / 46 5.5 System Status Error in the Self-check If the self-check does not terminate normally, your system may be malfunctioning. In such a case,

41 / 46 Chapter 6 Maintenance and Guarantee 6.1 Maintenance If dust or dirt collects on any equipment of your emulation system, wipe it off with a

42 / 46 6.4 How to Make Request for Repair If your product is found faulty, follow the procedure below to send your product for repair. Customer

43 / 46 Chapter 7 External Dimensions & Interface Cable Specifications 7.1 External Dimensions of the Emulator PC7501 Figure 7.1 External dim

44 / 46 7.2 LPT Parallel Interface Cable The LPT parallel interface connector used for emulator PC7501 is an IEEE1284-C (36-pin half-pitch) connecto

PC7501 User’s Manual Rev.3.00 June 1, 2004 REJ10J0078-0300T COPYRIGHT ©2004 RENESAS TECHNOLOGY CORPORATION AND RENESAS SOLUTIONS CORPORATION ALL R

5 / 46 Chapter 4 Setup 4.1 Connecting AC Adapter ...

6 / 46 Terminology Some specific words used in this user's manual are defined as follows: PC7501 system This means the emulator system built a

7 / 46 Chapter 1 Precautions for Safety This chapter describes the handling precautions to be followed when using the emulator PC7501. For precauti

8 / 46 WARNING Warnings for AC Power Supply: • If the attached AC power cable does not fit the receptacle, do not alter the AC power cable and do n

9 / 46 CAUTION Cautions for AC Adapter: • Use only the AC adapter included in this product package. • The included AC adapter is for PC7501. Do not