Renesas Emulation Pod M3062PT3-RPD-E Manual do Utilizador descarregar pdf (Página 2)

REJ05B0186-0202Z/Rev.2.02 August 2004 Page 2 of 11

M16C/62P, M16C/62A Group

Differences between M16C/62P and M16C/62A

Table 3.1.2 Function differences (mask ROM version and flash memory version)-2(Note1)

Note 1: About the details and the characteristics, refer to hardware manual.

Note 2: I

C is a trademark of Philips Semiconductors Corporation.

Note 3: IEBus is a trademark of NEC Electronics Corporation.

Item M16C/62P M16C/62A

Upper address memory

expansion mode and

microprocessor mode

P4_0 to P4_3(A16 to A19),

P3_4 to P3_7(A12 to A15)

: Switchable between address bus and I/O port

P4_0 to P4_3(A16 to A19)

: Switchable between address bus and I/O port

A12 to A15: No Switchable

Access to SFR Variable (1 to 2 waits) 1 wait fixed

Software wait to external

area

Variable (0 to 3 waits) Variable (0 to 1 wait)

Protect Can be set for PM0, PM1, PM2, CM0, CM1,

CM2, PLC0, INVC0, INVC1, PD9, S3C, S4C,

TB2SC, PCLKR, VCR2, D4INT registers

Can be set for PM0, PM1, CM0, CM1, PD9, S3C,

S4C registers

Watchdog timer

Watchdog timer interrupt or watchdog timer reset

is selected

Count source protective mode is available

Watchdog timer interrupt

No count source protective mode

Address match interrupt 4 2

Timers A, timer B

Count source

Selectable: f1, f2, f8, f32, fC32

Selectable: f1, f8, f32, fC32

Timer A two-phase pulse

signal processing

Function Z-phase (counter reset) input No function Z-phase (counter reset) input

Timer functions for

three-phase motor control

Function protect by protect register

Count source is selected f1, f2, f8, f32, fC32

Dead time timer count source is selected: f1, f1

divided by 2, f2, f2 divided by 2

Three-phase output forcible shutoff function

based on NMI input is available, output polarity

change, carrier wave phase detection

No function protected by protect register

Count source is selected :f1, f8, f32, fC32

Dead time timer count source is fixed at f1

divided by 2

Serial I/O

(UART0 to UART2)

(UART, Clock synchronous, I

C-bus

(Note 2),

IEBus

(Note 3)) x 3

(UART, Clock synchronous) x 2

(UART, Clock synchronous, I

C-bus

(Note 2),

IEBus

(Note 3)) x 1

UART0 to UART2,

SI/O3, SI/O4

Count source

Select from f1SIO, f2SIO, f8SIO, f32SIO Select from f1, f8, f32

Serial I/O

RTS timing

Assert low when receive buffer is read Assert low when reception is completed

UART0 to UART2

Overrun error occur timing

This error occurs if the serial I/O started receiving

the next data before reading the UiRB register

(i=0 to 2) and received the 7th bit of the next data

(Clock synchronous).

This error occurs if the serial I/O started receiving

the next data before reading the UiRB register

and received the bit one before the last stop bit of

the next data (UART).

This error occurs when the next data is ready

before contents of UiRB register (i=0 to 2) are

read out

Serial I/O

CTS/RTS separate function

Have None

UART2 data transmit timing After data was written, transfer starts at the 2nd

BRG overflow timing (same as UART0 and

UART1)

After data was written, transfer starts at the 1st

BRG overflow timing (Output starts one cycle of

BRG overflow earlier than UART0 and UART1)

Serial I/O

Sleep function

None Have

Serial I/O

C mode

Start condition, stop condition: Auto-generation

Start condition, stop condition:

Not auto-generation

Serial I/O

C mode

SDA delay

Only digital delay is selected as SDA delay

SDA digital delay count source: BRG

Analog or digital delay is selected as SDA delay.

SDA digital delay count source: 1/f(XIN)

SI/O3, SI/O4

Clock polarity

Selectable

Fixed

A/D converter

10 bits x 8 channels

Expandable up to 26 channels

10 bits x 8 channels

Expandable up to 10 channels

A/D converter

operation clock

Selectable: fAD, fAD divided by 2, 3, 4, 6, 12 Selectable: fAD, fAD/2, fAD/4

A/D converter input pin Select from ports P0, P2, P10 Fixed at port P10

1 2 3 4 5 6 7 ... 10 11

Comentários a estes Manuais

Sem comentários

Renesas Emulation Pod M3062PT3-RPD-E Manual do Utilizador Página 2

Comentários a estes Manuais

Manuais e produtos relacionados com Redes Renesas Emulation Pod M3062PT3-RPD-E