Renesas TFP-80C Informações Técnicas Página 1

To our customers, Old Company Name in Catalogs and Other Documents On April 1st, 2010, NEC Electronics Corporation merged with Renesas Technology C

V WARNING Observe the precautions listed below. Failure to do so will result in a FIRE HAZARD and will damage the user system and the emul

Cautions 1. Hitachi neither warrants nor grants licenses of any rights of Hitachi’s or any third party’s patent, copyright, trademark, or other inte

i Preface Thank you for purchasing this user system interface cable (HS3032ECN61H) for the Hitachi’s original microprocessor H8/3035 series, H8/3032

ii Contents Section 1 Configuration...1 Section 2 Connection P

1 Section 1 Configuration CAUTION Use an IC149-080-058-B51 socket (manufactured by YAMAICHI ELECTRONICS Co., Ltd.) for the TFP-80C package

2 Figure 1 HS3032ECN61H User System Interface Cable

3 Table 1 lists the HS3032ECN61H components. Please make sure you have all of these components when unpacking. Table 1 HS3032ECN61H Components No.

4 Section 2 Connection Procedures 2.1 Connecting User System Interface Cable to Emulator Station WARNING Observe the precautions listed below.

5 Figure 2 Connecting User System Interface Cable to Emulator Station

Notice 1. All information included in this document is current as of the date this document is issued. Such information, however, is subject to chang

6 2.2 Connecting User System Interface Cable to User System WARNING Always switch OFF the user system and the emulator product before the USE

7 2.2.4 Fastening Cable Head CAUTION 1. Use a Phillips-type screwdriver whose head matches the screw head. 2. The tightening torque must

8 Pin 1Cable headIC socket (IC149-080-058-B51manufactured by YAMAICHI ELECTRONICS Co., Ltd.)Screws (M2.6 x 12 mm)with flat washersUser system Figure

9 2.2.5 Fastening Cable Body Connect the cable body to the cable head. Cable bodyCable headRemove jigPush the remove jigRemovingUser system Figure 4

10 2.3 Recommended Dimensions for User System Mount Pad Figure 5 shows the recommended dimensions for the mount pad (footprint) for the user system

11 2.4 Dimensions for User System Interface Cable Head The dimensions for the user system interface cable head are shown in figure 6. 45.748.64.04

12 2.5 Resulting Dimensions after Connecting User System Interface Cable The resulting dimensions, after connecting the user system interface cable

13 Section 3 Installing the MCU to the User System CAUTION 1. Check the location of pin 1 before inserting. 2. Use a Phillips-type screwdrive

14 MCUPin 1IC socket (IC149-080-058-B51manufactured by YAMAICHI ELECTRONICS Co., Ltd.)User systemScrews (M2.6 x 8 mm)with flat washersSocket cover Fi

15 Section 4 Verifying Operation 1. When using the H8/3052 series E6000 emulator (HS3052EPI61H), turn on the emulator according to the procedures

Regarding the change of names mentioned in the document, such as Hitachi Electric and Hitachi XX, to Renesas Technology Corp.The semiconductor operati

16 Section 5 Notice 1. Make sure that pin 1 on the user system IC socket is correctly aligned with pin 1 on the cable head before inserting the ca

H8/3035 Series, H8/3032 Series H8/3005, H8/3004 TFP-80C User System Interface Cable(HS3032ECN61H) for E6000 EmulatorUser’s ManualUser’s Manual

I IMPORTANT INFORMATION READ FIRST • READ this user's manual before using this user system interface cable. • KEEP the user's manual handy

II LIMITED WARRANTY Hitachi warrants its user system interface cables to be manufactured in accordance with published specifications and free

III State Law: Some states do not allow the exclusion or limitation of implied warranties or liability for incidental or consequential damages, so

IV SAFETY PAGE READ FIRST • READ this user's manual before using this user system interface cable. • KEEP the user's manual handy for futur