Renesas PCA7429G02 Informações Técnicas descarregar pdf (Página 101)

Max.

200

100

0.4

3.0

0.4

0.6

1.3

130

CC = 5.5V,

f(X

IN) = 8MHz

CC = 5.5V, f(XIN) = 0,

f(X

CIN) = 32kHz,

OSD OFF, Data slicer OFF,

Low-power dissipation mode set

(CM5 = “0”, CM6 = “1”)

CC = 5.5 V, f(XIN) = 8 MHz

CC = 5.5 V, f(XIN) = 0,

f(X

CIN) = 32 kHz,

Low-power dissipation mode set

(CM5 = “0”, CM6 = “1”)

CC = 5.5V, f(XIN) = 0,

f(X

CIN) = 0

CC = 4.5 V

OH = –0.5 mA

CC = 4.5 V

OL = 0.5 mA

CC = 4.5 V

OL = 10.0 mA

CC = 4.5 V

CC = 5.0 V

CC = 5.5 V

I = 5.5 V

CC = 5.5 V

I = 0 V

CC = 5.5 V

I = 12 V

CC = 4.5 V

12. ELECTRIC CHARACTERISTICS (VCC = 5 V ± 10 %, VSS = 0 V, f(XIN) = 8 MHz, Ta = –10 °C to 70 °C, unless otherwise noted)

Notes 1: The total current that flows out of the IC must be 20 mA or less.

2: The total input current to IC (I

OL1 + IOL2 + IOL3) must be 30 mA or less.

3: The total average input current for ports P3

0, P31, P24 and P25 and AVCC–VSS to IC must be 20 mA or less.

4: Connect 0.1 µF or more capacitor externally between the power source pins V

CC–VSS and AVCC–VSS so as to reduce power source noise.

Also connect 0.1 µF or more capacitor externally between the pins V

CC–CNVSS.

5: Use a quartz-crystal oscillator or a ceramic resonator for the CPU oscillation circuit. When using the data slicer, use 8 MHz.

6: P0

6, P07, P15, P23, P24 have the hysteresis when these pins are used as interrupt input pins or timer input pins. P11–P14 have the hysteresis when these

pins are used as multi-master I

C-BUS interface ports. P20–P22 have the hysteresis when these pins are used as serial I/O pins.

7: Pin names in each parameter is described as below.

(1) Dedicated pins: dedicated pin names.

(2) Duble-/triple-function ports

• When the same limits: I/O port name.

• When the limits of functins except ports are different from I/O port limits: function pin name.

HIGH output voltage P10–P17, P20–P27,

0, P31, P52–P55,

LOW output voltage P0

0–P07, P10,

5–P17, P20–P23,

6, P27, P52–P55

LOW output voltage P24, P25, P30, P31

LOW output voltage P11–P14

Hysteresis (See note 6)

RESET, P5

0, P51, INT1, INT2,

INT3, TIM2, TIM3, S

IN, SCLK, SCL1,

SCL2, SDA1, SDA2

HIGH input leak current

6, P07, P10–P17, P20–P27,

0, P31, RESET, P50, P51,

HIGH input leak current

0–P07, P10–P17, P20–P27, P30,

1, P50, P51, RESET

HIGH output leak current

0–P05

C-BUS • BUS switch connection resistor

(between SCL1 and SCL2, SDA1 and SDA2)

Symbol Parametear

Test conditions

OSD OFF

Data slicer OFF

OSD ON

Data slicer ON

Stop mode

Wait mode

System operation

Power source current

VOH

VOL

VT+ –VT–

IZH

IIZL

IOZH

RBS

Test

circuit

Min.

2.4

Limits

OL = 3 mA

OL = 6 mA

Typ.

0.5

Unit

Ω

SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER

and ON-SCREEN DISPLAY CONTROLLER

M37272M6/M8–XXXSP/FP, M37272MA–XXXSP

M37272E8SP/FP, M37272EFSP

MITSUBISHI MICROCOMPUTERS

Rev. 1.4

1 2 ... 96 97 98 99 100 101 102 103 104 105 106 ... 144 145

Comentários a estes Manuais

Sem comentários

Renesas PCA7429G02 Informações Técnicas Página 101

Comentários a estes Manuais

Manuais e produtos relacionados com Descodificadores Renesas PCA7429G02