Renesas R8C/15 Informações Técnicas Página 137
- Página / 279
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
R8C/14 Group, R8C/15 Group 13. Timers
Rev.2.10 Jan 19, 2006 Page 123 of 253
REJ09B0164-0210
13.3.2 Output Compare Mode
Output compare mode is mode to generate an interrupt request when the value of the TC register
matches the value of the TM0 or TM1 register. Table 13.12 shows Specification of Output Compare
Mode. Figure 13.31 shows an Operating Example in Output Compare Mode.
NOTES:
1. When the corresponding port data is “1”, the waveform is output depending on the setting of the
registers TCC1 and TCOUT. When the corresponding port data is “0”, the fixed level is output (refer
to Figure 13.25 Block Diagram of CMP Waveform Output Unit).
2. Access the TC, TM0, and TM1 registers in 16-bit units.
Table 13.12 Specification of Output Compare Mode
Item Specification
Count Source f1, f8, f32, fRING-fast
Count Operation • Increment
• The value in the TC register is set to “0000h” when a count stops
Count Start Condition The TCC00 bit in the TCC0 register is set to “1” (count starts)
Counter Stop Condition The TCC00 bit in the TCC0 register is set to “0” (count stops)
Waveform Output Start
Condition
The TCOUT0 to TCOUT5 bits in the TCOUT register is set to “1” (enables
CMP output).
(2)
Waveform Output Stop
Condition
The TCOUT0 to TCOUT5 bits in the TCOUT register is set to “0” (disables
CMP output).
Interrupt Request
Generation Timing
• When a match occurs in the compare circuit 0 [compare 0 interrupt]
• When a match occurs in the compare circuit 1 [compare 1 interrupt]
• When Time C overflows [Timer C interrupt]
INT3
/TCIN Pin Function Programmable I/O port or INT3 interrupt input
P1_0 to P1_2 Pins and
P3_0 to P3_2 Pins
Function
Programmable I/O port or CMP output
(1)
Counter Value Reset
Timing
When the TCC00 bit in the TCC0 register is set to “0” (count stops)
Read from Timer
(1)
• The value in the compare register can be read out by reading the TM0 and
TM1 registers.
• The count value can be read out by reading the TC register.
Write to Timer
(1)
• Write to the TC register is disabled.
• The values written to the TM0 and TM1 registers are stored in the compare
register at the following timings:
- When the TM0 and TM1 registers are written if the TCC00 bit is set to “0”
(count stops)
- When the counter overflows if the TCC00 bit is set to “1” (during
counting) and the TCC12 bit in the TCC1 register is set to “0” (free-run)
- When the compare 1 matches a counter if the TCC00 bit is set to “1” and
the TCC12 bit is set to “1” (set the TC register to “0000h” when the
compare 1 matches)
Select Function • Timer C counter reload select function
The TCC12 bit in the TCC1 register can select whether the counter value
in the TC register is set to “0000h” when the compare circuit 1 matches or
not.
• The TCC14 to TCC15 bits in the TCC1 register can select the output level
when the compare circuit 0 matches. The TCC16 to TCC17 bits in the
TCC1 register can select the output level when the compare circuit 1
matches.
• The TCOUT6 to TCOUT7 bits in the TCOUT register can select whether
the output is reversed or not.
- To our customers 1
- R8C/14 Group 3
- R8C/15 Group 3
- How to Use This Manual 5
- 3. M16C Family Documents 6
- Table of Contents 7
- 10. Protection 55 9
- 11. Interrupt 56 9
- 12. Watchdog Timer 78 9
- 13. Timers 83 9
- 14. Serial Interface 125 10
- 16. A/D Converter 168 10
- 18. Flash Memory Version 191 11
- 20. Precautions 235 11
- SFR Page Reference 13
- R8C/14 Group, R8C/15 Group 15
- 1. Overview 15
- 1.2 Performance Overview 16
- 1.3 Block Diagram 18
- Type No. R 5 F 21 14 4 D SP 19
- Type No. R 5 F 21 15 4 D SP 20
- 1.5 Pin Assignments 21
- 1.6 Pin Description 22
- 2.8.10 Reserved Bit 26
- 3. Memory 27
- 3.2 R8C/15 Group 28
- Table 4.2 SFR Information(2) 30
- Table 4.3 SFR Information(3) 31
- Table 4.4 SFR Information(4) 32
- 5. Reset 33
- to P3_5, P3_7 Input Port 34
- to P4_7 Input Port 34
- 5.1 Hardware Reset 35
- 5.1.2 Power on 35
- Power Supply 36
- Voltage Detection 36
- 5.2 Power-On Reset Function 37
- 5.3 Voltage Monitor 1 Reset 38
- 5.4 Voltage Monitor 2 Reset 38
- 5.5 Watchdog Timer Reset 38
- 5.6 Software Reset 38
- 6. Voltage Detection Circuit 39
- Figure 6.5 VW1C Register 43
- Figure 6.6 VW2C Register 44
- 6.1.1 Monitoring Vdet1 45
- 6.1.2 Monitoring Vdet2 45
- 6.2 Voltage Monitor 1 Reset 46
- 7. Processor Mode 49
- Figure 7.2 PM1 Register 50
- 9. Clock Generation Circuit 52
- Figure 9.2 CM0 Register 54
- Figure 9.3 CM1 Register 55
- Figure 9.4 OCD Register 56
- Figure 9.5 HRA0 Register 57
- 9.1 Main Clock 59
- 9.2 On-Chip Oscillator Clock 60
- 9.4 Power Control 62
- 9.4.1 Normal Operating Mode 62
- 9.4.2.4 Exiting Wait Mode 64
- 9.4.3 Stop Mode 65
- 9.4.3.1 Entering Stop Mode 65
- 9.4.3.3 Exiting Stop Mode 65
- 10. Protection 69
- 11. Interrupt 70
- 11.1.2 Software Interrupts 71
- 11.1.2.2 Overflow Interrupt 71
- 11.1.2.3 BRK Interrupt 71
- 11.1.5.1 Fixed Vector Tables 73
- 11.1.6 Interrupt Control 75
- Figure 11.4 INT0IC Register 76
- 11.1.6.1 I Flag 77
- 11.1.6.2 IR Bit 77
- 11.1.6.4 Interrupt Sequence 78
- Instruction in 79
- 11.1.6.7 Saving a Register 80
- 11.1.6.9 Interrupt Priority 81
- Level 0 (default value) 82
- 11.2 INT Interrupt 83
- 11.2.1 INT0 Interrupt 83
- 11.2.2 INT0 Input Filter 84
- Timer X Mode Register 85
- 11.2.4 INT3 Interrupt 86
- Figure 11.16 TCC1 Register 87
- 11.3 Key Input Interrupt 88
- Figure 11.18 KIEN Register 89
- 11.4 Address Match Interrupt 90
- 12. Watchdog Timer 92
- 13. Timers 97
- CNTRSEL=1 98
- CNTRSEL=0 98
- Figure 13.2 TXMR Register 99
- REJ09B0164-0210 100
- 13.1.1 Timer Mode 101
- 13.1.2 Pulse Output Mode 102
- 13.1.3 Event Counter Mode 104
- Input polarity selected to 112
- Figure 13.12 TZMR Register 113
- Figure 13.15 TCSS Register 116
- 13.2.1 Timer Mode 117
- • When count starts 119
- Timer Z Mode Register 127
- PREZ=01h, TZPR=01h, TZSC=02h 128
- 13.3 Timer C 129
- Timer C Register 131
- Figure 13.27 TCC0 Register 132
- Figure 13.28 TCC1 Register 133
- Figure 13.29 TCOUT Register 134
- 13.3.1 Input Capture Mode 135
- ←Measurement value 1 136
- ←Measurement value 2 136
- 13.3.2 Output Compare Mode 137
- 14. Serial Interface 139
- UART0 Bit Rate Register 141
- Set to “001b” 145
- 14.2.2 Bit Rate 153
- Figure 15.2 SSCRH Register 156
- SS Control Register L 157
- 15.1 Transfer Clock 163
- 15.3 Interrupt Requests 166
- 15.5.2 Data Transmit 169
- 15.5.3 Data Receive 171
- 15.5.4 Data Transmit/Receive 173
- I/O Pin and SS Shift Register 175
- 15.1.1 Association 175
- 15.6.2 Data Transmit 177
- 15.6.3 Data Receive 179
- 16. A/D Converter 182
- 16.1 One-Shot Mode 186
- 16.2 Repeat Mode 188
- 16.3 Sample and Hold 190
- 16.4 A/D Conversion Cycles 190
- 17. Programmable I/O Ports 193
- P1_0 to P1_3 194
- P1_6, P1_7 195
- P3_4, P3_5, P3_7 195
- P4_6/XIN 196
- P4_7/XOUT 196
- 17.4 Port setting 200
- 17.5 Unassigned Pin Handling 204
- 18. Flash Memory Version 205
- 18.2 Memory Map 207
- 18.3.1 ID Code Check Function 209
- Figure 18.4 OFS Register 210
- 18.4 CPU Rewrite Mode 211
- 18.4.1 EW0 Mode 212
- 18.4.2 EW1 Mode 212
- Full Status Check 213
- 18.4.2.10 FMR40 bit 214
- 18.4.2.11 FMR41 bit 214
- 18.4.2.12 FMR46 bit 214
- EW1 Mode Operating Procedure 217
- →wait until oscillation 218
- 18.4.3 Software Commands 219
- 18.4.3.1 Read Array Command 219
- 18.4.3.4 Program Command 220
- 18.4.3.5 Block Erase 221
- 18.4.4 Status Register 223
- 18.4.5 Full Status Check 224
- 18.5 Standard Serial I/O Mode 226
- 18.5.1 ID Code Check Function 226
- R8C/14, R8C/15 228
- 18.6 Parallel I/O Mode 230
- SSO(Output) 240
- SSI(Input) 240
- VCC = 5V 244
- VCC = 3V 248
- 20. Precautions 249
- 20.2 Interrupts 250
- 20.2.1 Reading Address 00000h 250
- 20.2.2 SP Setting 250
- 20.3 Clock Generation Circuit 253
- 20.4 Timers 254
- 20.4.1 Timers X and Z 254
- 20.4.2 Timer X 254
- 20.4.3 Timer Z 255
- 20.4.4 Timer C 255
- 20.5 Serial Interface 256
- 20.7 A/D Converter 258
- 20.8 Flash Memory Version 259
- 20.8.1 CPU Rewrite Mode 259
- 20.8.1.1 Operating Speed 259
- 20.8.1.3 Interrupts 259
- 20.8.1.9 Interrupt Request 260
- Generation during Auto-erase 260
- Operation in EW1 Mode 260
- 20.9 Noise 262
- Debugging Emulator 265
- Register Index 267
- REVISION HISTORY 268
- → “INT1” 271
- → Figure 18.16 276
- “8.16” → “8.56” 277
- Rev.2.10 Jan 19, 2006 278
- Renesas Technology Corp 278
- Hardware Manual 279
Manuais e produtos relacionados com Redes Renesas R8C/15
Redes Renesas H8S/2378F Informações Técnicas
(170 páginas)
(170 páginas)
Redes Renesas HS2378KCI01H Informações Técnicas
(42 páginas)
(42 páginas)
Redes Renesas 70 Informações Técnicas
(49 páginas)
(49 páginas)
Redes Renesas HS1653ECN61H Manual do Utilizador
(322 páginas)
(322 páginas)
Redes Renesas SuperH SH7285 Manual do Utilizador
(60 páginas)
(60 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.054 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais