Renesas R8C/15 Informações Técnicas Página 96
- Página / 279
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
R8C/14 Group, R8C/15 Group 12. Watchdog Timer
Rev.2.10 Jan 19, 2006 Page 82 of 253
REJ09B0164-0210
12.2 When Count Source Protection Mode Enabled
The count source of the watchdog timer is the low-speed on-chip oscillator clock when count source
protection mode is enabled. If the CPU clock stops when the program is out of control, the clock can be
supplied to the watchdog timer. Table 12.3 lists the Specification of Watchdog Timer (When Count
Source Protection Mode is Enabled).
NOTES:
1. The WDTON bit cannot be changed by a program. When setting the WDTON bit, write “0” to the bit
0 of the address 0FFFFh by a flash writer.
2. Even if writing “0” to the CSPROINI bit in the OFS register, the CSPRO bit is set to “1”. The
CSPROINI bit cannot be changed by a program. When setting the CSPROINI bit, write “0” to the bit
7 of the address 0FFFFh by a flash writer.
Table 12.3 Specification of Watchdog Timer (When Count Source Protection Mode is Enabled)
Item Specification
Count Source Low-speed on-chip oscillator clock
Count Operation Decrement
Period Count value of watchdog timer (4096)
Low-speed on-chip oscillator clock
e.g. Period is approximately 32.8ms when the low-speed on-chip
oscillator clock is 125 kHz
Count Start Condition
The WDTON bit
(1)
in the OFS register (0FFFFh) selects the operation
of the watchdog timer after reset.
• When the WDTON bit is set to “1” (watchdog timer is in stop state
after reset)
The watchdog timer and prescaler stop after reset and the count
starts by writing to the WDTS register
• When the WDTON bit is set to “0” (watchdog timer starts
automatically after reset)
The watchdog timer and prescaler start counting automatically after
reset
Reset Condition of Watchdog
Timer
• Reset
• Write “00h” to the WDTR register before writing “FFh”
• Underflow
Count Stop Condition None (the count does not stop in wait mode after the count starts. The
microcomputer does not enter stop mode)
Operation at the time of
Underflow
Watchdog timer reset (refer to 5.5 Watchdog Timer Reset)
Register, Bit • When setting the CSPPRO bit in the CSPR register to “1” (count
source protection mode is enabled)
(2)
, the following are set
automatically
- Set 0FFFh to the watchdog timer
- Set the CM14 bit in the CM1 register to “0” (low-speed on-chip
oscillator on)
- Set the PM12 bit in the PM1 register to “1” (The watchdog timer is
reset when watchdog timer underflows)
• The following states are held in count source protection mode
- Writing to the CM10 bit in the CM1 register disables (It remains
unchanged even if it is set to “1”. The microcomputer does not
enter stop mode)
- Writing to the CM14 bit in the CM1 register disables (It remains
unchanged even if it is set to “1”. The low-speed on-chip oscillator
does not stop)
- To our customers 1
- R8C/14 Group 3
- R8C/15 Group 3
- How to Use This Manual 5
- 3. M16C Family Documents 6
- Table of Contents 7
- 10. Protection 55 9
- 11. Interrupt 56 9
- 12. Watchdog Timer 78 9
- 13. Timers 83 9
- 14. Serial Interface 125 10
- 16. A/D Converter 168 10
- 18. Flash Memory Version 191 11
- 20. Precautions 235 11
- SFR Page Reference 13
- R8C/14 Group, R8C/15 Group 15
- 1. Overview 15
- 1.2 Performance Overview 16
- 1.3 Block Diagram 18
- Type No. R 5 F 21 14 4 D SP 19
- Type No. R 5 F 21 15 4 D SP 20
- 1.5 Pin Assignments 21
- 1.6 Pin Description 22
- 2.8.10 Reserved Bit 26
- 3. Memory 27
- 3.2 R8C/15 Group 28
- Table 4.2 SFR Information(2) 30
- Table 4.3 SFR Information(3) 31
- Table 4.4 SFR Information(4) 32
- 5. Reset 33
- to P3_5, P3_7 Input Port 34
- to P4_7 Input Port 34
- 5.1 Hardware Reset 35
- 5.1.2 Power on 35
- Power Supply 36
- Voltage Detection 36
- 5.2 Power-On Reset Function 37
- 5.3 Voltage Monitor 1 Reset 38
- 5.4 Voltage Monitor 2 Reset 38
- 5.5 Watchdog Timer Reset 38
- 5.6 Software Reset 38
- 6. Voltage Detection Circuit 39
- Figure 6.5 VW1C Register 43
- Figure 6.6 VW2C Register 44
- 6.1.1 Monitoring Vdet1 45
- 6.1.2 Monitoring Vdet2 45
- 6.2 Voltage Monitor 1 Reset 46
- 7. Processor Mode 49
- Figure 7.2 PM1 Register 50
- 9. Clock Generation Circuit 52
- Figure 9.2 CM0 Register 54
- Figure 9.3 CM1 Register 55
- Figure 9.4 OCD Register 56
- Figure 9.5 HRA0 Register 57
- 9.1 Main Clock 59
- 9.2 On-Chip Oscillator Clock 60
- 9.4 Power Control 62
- 9.4.1 Normal Operating Mode 62
- 9.4.2.4 Exiting Wait Mode 64
- 9.4.3 Stop Mode 65
- 9.4.3.1 Entering Stop Mode 65
- 9.4.3.3 Exiting Stop Mode 65
- 10. Protection 69
- 11. Interrupt 70
- 11.1.2 Software Interrupts 71
- 11.1.2.2 Overflow Interrupt 71
- 11.1.2.3 BRK Interrupt 71
- 11.1.5.1 Fixed Vector Tables 73
- 11.1.6 Interrupt Control 75
- Figure 11.4 INT0IC Register 76
- 11.1.6.1 I Flag 77
- 11.1.6.2 IR Bit 77
- 11.1.6.4 Interrupt Sequence 78
- Instruction in 79
- 11.1.6.7 Saving a Register 80
- 11.1.6.9 Interrupt Priority 81
- Level 0 (default value) 82
- 11.2 INT Interrupt 83
- 11.2.1 INT0 Interrupt 83
- 11.2.2 INT0 Input Filter 84
- Timer X Mode Register 85
- 11.2.4 INT3 Interrupt 86
- Figure 11.16 TCC1 Register 87
- 11.3 Key Input Interrupt 88
- Figure 11.18 KIEN Register 89
- 11.4 Address Match Interrupt 90
- 12. Watchdog Timer 92
- 13. Timers 97
- CNTRSEL=1 98
- CNTRSEL=0 98
- Figure 13.2 TXMR Register 99
- REJ09B0164-0210 100
- 13.1.1 Timer Mode 101
- 13.1.2 Pulse Output Mode 102
- 13.1.3 Event Counter Mode 104
- Input polarity selected to 112
- Figure 13.12 TZMR Register 113
- Figure 13.15 TCSS Register 116
- 13.2.1 Timer Mode 117
- • When count starts 119
- Timer Z Mode Register 127
- PREZ=01h, TZPR=01h, TZSC=02h 128
- 13.3 Timer C 129
- Timer C Register 131
- Figure 13.27 TCC0 Register 132
- Figure 13.28 TCC1 Register 133
- Figure 13.29 TCOUT Register 134
- 13.3.1 Input Capture Mode 135
- ←Measurement value 1 136
- ←Measurement value 2 136
- 13.3.2 Output Compare Mode 137
- 14. Serial Interface 139
- UART0 Bit Rate Register 141
- Set to “001b” 145
- 14.2.2 Bit Rate 153
- Figure 15.2 SSCRH Register 156
- SS Control Register L 157
- 15.1 Transfer Clock 163
- 15.3 Interrupt Requests 166
- 15.5.2 Data Transmit 169
- 15.5.3 Data Receive 171
- 15.5.4 Data Transmit/Receive 173
- I/O Pin and SS Shift Register 175
- 15.1.1 Association 175
- 15.6.2 Data Transmit 177
- 15.6.3 Data Receive 179
- 16. A/D Converter 182
- 16.1 One-Shot Mode 186
- 16.2 Repeat Mode 188
- 16.3 Sample and Hold 190
- 16.4 A/D Conversion Cycles 190
- 17. Programmable I/O Ports 193
- P1_0 to P1_3 194
- P1_6, P1_7 195
- P3_4, P3_5, P3_7 195
- P4_6/XIN 196
- P4_7/XOUT 196
- 17.4 Port setting 200
- 17.5 Unassigned Pin Handling 204
- 18. Flash Memory Version 205
- 18.2 Memory Map 207
- 18.3.1 ID Code Check Function 209
- Figure 18.4 OFS Register 210
- 18.4 CPU Rewrite Mode 211
- 18.4.1 EW0 Mode 212
- 18.4.2 EW1 Mode 212
- Full Status Check 213
- 18.4.2.10 FMR40 bit 214
- 18.4.2.11 FMR41 bit 214
- 18.4.2.12 FMR46 bit 214
- EW1 Mode Operating Procedure 217
- →wait until oscillation 218
- 18.4.3 Software Commands 219
- 18.4.3.1 Read Array Command 219
- 18.4.3.4 Program Command 220
- 18.4.3.5 Block Erase 221
- 18.4.4 Status Register 223
- 18.4.5 Full Status Check 224
- 18.5 Standard Serial I/O Mode 226
- 18.5.1 ID Code Check Function 226
- R8C/14, R8C/15 228
- 18.6 Parallel I/O Mode 230
- SSO(Output) 240
- SSI(Input) 240
- VCC = 5V 244
- VCC = 3V 248
- 20. Precautions 249
- 20.2 Interrupts 250
- 20.2.1 Reading Address 00000h 250
- 20.2.2 SP Setting 250
- 20.3 Clock Generation Circuit 253
- 20.4 Timers 254
- 20.4.1 Timers X and Z 254
- 20.4.2 Timer X 254
- 20.4.3 Timer Z 255
- 20.4.4 Timer C 255
- 20.5 Serial Interface 256
- 20.7 A/D Converter 258
- 20.8 Flash Memory Version 259
- 20.8.1 CPU Rewrite Mode 259
- 20.8.1.1 Operating Speed 259
- 20.8.1.3 Interrupts 259
- 20.8.1.9 Interrupt Request 260
- Generation during Auto-erase 260
- Operation in EW1 Mode 260
- 20.9 Noise 262
- Debugging Emulator 265
- Register Index 267
- REVISION HISTORY 268
- → “INT1” 271
- → Figure 18.16 276
- “8.16” → “8.56” 277
- Rev.2.10 Jan 19, 2006 278
- Renesas Technology Corp 278
- Hardware Manual 279
Manuais e produtos relacionados com Redes Renesas R8C/15
Redes Renesas H8S/2378F Informações Técnicas
(170 páginas)
(170 páginas)
Redes Renesas HS2378KCI01H Informações Técnicas
(42 páginas)
(42 páginas)
Redes Renesas 70 Informações Técnicas
(49 páginas)
(49 páginas)
Redes Renesas HS1653ECN61H Manual do Utilizador
(322 páginas)
(322 páginas)
Redes Renesas SuperH SH7285 Manual do Utilizador
(60 páginas)
(60 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.027 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais