Renesas M16C/6NK Informações Técnicas Página 215
- Página / 412
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Rev.2.10 Apr 14, 2006 page 191 of 378
REJ09B0124-0210
M16C/6N Group (M16C/6NK, M16C/6NM) 15. Serial Interface
Item Specification
Transfer data format • Direct format
• Inverse format
Transfer clock • The CKDIR bit in the U2MR register = 0 (internal clock) : fi/(16(n+1))
fi = f1SIO, f2SIO, f8SIO, f32SIO. n: Setting value of the U2BRG register 00h to FFh
• The CKDIR bit = 1 (external clock) : fEXT/(16(n+1))
fEXT: Input from CLK2 pin. n: Setting value of the U2BRG register 00h to FFh
Transmit start condition Before transmission can start, meet the following requirements
• The TE bit in the U2C1 register = 1 (transmission enabled)
• The TI bit in the U2C1 register = 0 (data present in the U2TB register)
Receive start condition Before reception can start, meet the following requirements
• The RE bit in the U2C1 register = 1 (reception enabled)
• Start bit detection
• For transmission
When the serial interface finished sending data from the U2TB transfer register
(U2IRS bit = 1)
• For reception
When transferring data from the UART2 receive register to the U2RB register (at
completion of reception)
Error detection • Overrun error
(1)
This error occurs if the serial interface started receiving the next data before reading
the U2RB register and received the bit one before the last stop bit of the next data
• Framing error
(3)
This error occurs when the number of stop bits set is not detected
• Parity error
(3)
During reception, if a parity error is detected, parity error signal is output from the
TXD2 pin.
During transmission, a parity error is detected by the level of input to the RXD2 pin
when a transmission interrupt occurs
• Error sum flag
This flag is set to 1 when any of the overrun, framing, and parity errors is encountered
15.1.6 Special Mode 4 (SIM Mode) (UART2)
Based on UART mode, this is an SIM interface compatible mode. Direct and inverse formats can be
implemented, and this mode allows to output a low from the TXD2 pin when a parity error is detected.
Table 15.17 lists the SIM Mode Specifications. Table 15.18 lists the Registers to be Used and Settings in
SIM Mode. Figure 15.32 shows the Transmit and Receive Riming in SIM Mode.
Table 15.17 SIM Mode Specifications
Interrupt request
generation timing
(2)
NOTES:
1. If an overrun error occurs, the value of the U2RB register will be undefined. The IR bit in the S2RIC
register remains unchanged.
2. A transmit interrupt request is generated by setting the U2IRS bit in the U2C1 register to 1 (transmission
completed) and U2ERE bit in the U2C1 register to 1 (error signal output) after reset. Therefore, when
using SIM mode, set the IR bit to 0 (interrupt not requested) after setting these bits.
3. The timing at which the framing error flag and the parity error flag are set is detected when data is
transferred from the UARTi receive register to the UiRB register.
- To our customers 1
- Hardware Manual 3
- RENESAS MCU 3
- M16C FAMILY / M16C/60 SERIES 3
- Blank page 6
- How to Use This Manual 7
- 3. Register Notation 9
- Table of Contents 11
- __________ 12
- SFR Page Reference 17
- 1. Overview 25
- 1.2 Performance Overview 26
- 1.3 Block Diagram 28
- 1.4 Product Information 29
- 1.5 Pin Assignments 30
- M16C/6N Group 33
- (M16C/6NM) 33
- 1.6 Pin Functions 37
- 3. Memory 42
- 5. Resets 59
- 5.2 Software Reset 61
- 5.3 Watchdog Timer Reset 61
- 5.5 Internal Space 61
- 6. Processor Mode 62
- 6.2 Setting Processor Modes 63
- Processor Mode Register 0 64
- Processor Mode Register 1 65
- 7.1 Bus Mode 69
- 7.1.1 Separate Bus 69
- 7.1.2 Multiplexed Bus 69
- 7.2 Bus Control 70
- 7.2.2 Data Bus 70
- 7.2.3 Chip Select Signal 70
- 7.2.1 Address Bus 70
- 7.2.4 Read and Write Signals 72
- 7.2.5 ALE Signal 72
- 7.2.6 RDY Signal 73
- HOLD > DMAC > CPU 74
- 7.2.10 Software Wait 76
- 8. Clock Generation Circuit 80
- Figure 8.2 CM0 Register 82
- Figure 8.3 CM1 Register 83
- Figure 8.4 CM2 Register 84
- Figure 8.5 PCLKR Register 85
- CAN0/1 Clock Select Register 86
- PLL Control Register 0 87
- 8.1.1 Main Clock 88
- 8.1.2 Sub Clock 89
- 8.1.4 PLL Clock 90
- 8.2.1 CPU Clock and BCLK 92
- 8.3 Clock Output Function 92
- 8.4 Power Control 93
- 8.4.1 Normal Operating Mode 93
- 8.4.2 Wait Mode 95
- 8.4.3 Stop Mode 97
- REJ09B0124-0210 100
- State after Transition 101
- Current State 101
- 9. Protection 104
- 10.1 Type of Interrupts 105
- 10.2 Software Interrupts 106
- 10.2.2 Overflow Interrupt 106
- 10.2.3 BRK Interrupt 106
- 10.3 Hardware Interrupts 107
- 10.3.1 Special Interrupts 107
- 10.4.1 Fixed Vector Tables 108
- ________ 109
- 10.5 Interrupt Control 110
- Interrupt Control Register 111
- 10.5.1 I Flag 112
- 10.5.2 IR Bit 112
- 10.5.4 Interrupt Sequence 113
- _________ 114
- 10.5.7 Saving Registers 115
- 10.5.9 Interrupt Priority 116
- 10.6 INT Interrupt 118
- Figure 10.11 IFSR0 Register 119
- Figure 10.12 IFSR1 Register 120
- Figure 10.13 IFSR2 Register 121
- 10.7 NMI Interrupt 122
- 10.8 Key Input Interrupt 122
- 10.9 CAN0/1 Wake-up Interrupt 122
- 10.10 Address Match Interrupt 123
- 11. Watchdog Timer 125
- 12. DMAC 127
- ________ ________ 128
- Figure 12.2 DM0SL Register 129
- 12.1 Transfer Cycle 132
- 12.1.4 Effect of RDY Signal 132
- 12.2 DMA Transfer Cycles 134
- 12.3 DMA Enable 135
- 12.4 DMA Request 135
- 13. Timers 137
- 13.1 Timer A 139
- Up/Down Flag 141
- Count Start Flag 141
- One-Shot Start Flag 142
- Trigger Select Register 142
- Clock Prescaler Reset Flag 142
- 13.1.1 Timer Mode 143
- 13.1.2 Event Counter Mode 144
- 13.1.3 One-shot Timer Mode 149
- 13.2 Timer B 154
- 13.2.1 Timer Mode 157
- 13.2.2 Event Counter Mode 158
- Figure 13.20 160
- Figure 14.2 INVC0 Register 164
- Figure 14.3 INVC1 Register 165
- Dead Time Timer 166
- Timer B2 Register 167
- (1) (2) (3) 168
- Timer B2 Mode Register 170
- 15. Serial Interface 173
- _______ _______ 183
- _________ _________ 183
- Setting in UART Mode 191
- 15.1.3 Special Mode 1 (I 199
- Figure 15.23 I 200
- C Mode Block Diagram 200
- _______ ________ 201
- _______ ________ _______ 201
- Function 202
- 15.1.4 Special Mode 2 208
- Undefined 212
- (NOTE 2) 214
- (1) Transmit timing 217
- (2) Receive timing 217
- SIM card 218
- (1) Direct format 219
- (2) Inverse format 219
- 15.2 SI/Oi (i = 3 to 6) 220
- Bit Symbol 222
- 15.2.1 SI/Oi Operation Timing 224
- 15.2.2 CLK Polarity Selection 224
- 16. A/D Converter 226
- A/D Control Register 0 228
- A/D Control Register 1 228
- A/D Control Register 2 229
- A/D Register i (i = 0 to 7) 229
- 16.1 Mode Description 230
- 16.1.1 One-shot Mode 230
- 16.1.2 Repeat Mode 232
- 16.1.3 Single Sweep Mode 234
- 16.1.4 Repeat Sweep Mode 0 236
- 16.1.5 Repeat Sweep Mode 1 238
- 16.2 Function 240
- 16.2.2 Sample and Hold 240
- Data bus low-order 243
- D/A Control Register 244
- D/A Register i (i = 0, 1) 244
- 18. CRC Calculation 245
- Figure 18.3 CRC Calculation 246
- 19. CAN Module 247
- 19.1.3 CAN SFR Registers 248
- 19.4 CAN SFR Registers 252
- 19.5 Operational Modes 258
- Module idle 259
- Module transmits 259
- Module receives 259
- 19.5.5 Bus Off State 260
- CCLKR register 261
- CAN module 261
- 19.8 Bit-rate 262
- 19.11 Basic CAN Mode 265
- 19.14 Listen-Only Mode 266
- 19.15.1 Reception 268
- 19.15.2 Transmission 269
- 19.16 CAN Interrupt 270
- 20. Programmable I/O Ports 271
- 20.4 PCR Register 272
- Figure 20.1 I/O Ports (1) 273
- Figure 20.2 I/O Ports (2) 274
- Figure 20.3 I/O Ports (3) 275
- (inside dotted-line 276
- included) 276
- not included) 276
- Figure 20.5 I/O Ports (5) 277
- Figure 20.6 I/O Pins 277
- Port P8 Direction Register 278
- Port P8 Register 279
- Pull-up Control Register 0 280
- Pull-up Control Register 1 280
- Pull-up Control Register 2 280
- Port Control Register 281
- 21. Flash Memory Version 284
- 21.1 Memory Map 285
- 21.1.1 Boot Mode 286
- 21.2.2 ID Code Check Function 286
- Figure 21.2 ROMCP Register 287
- 21.3 CPU Rewrite Mode 288
- 21.3.1 EW0 Mode 289
- 21.3.2 EW1 Mode 289
- Power Dissipation Mode 294
- 21.3.5 Software Commands 297
- 21.3.6 Data Protect Function 302
- 21.3.8 Full Status Check 304
- 21.4 Standard Serial I/O Mode 306
- 21.4.1 ID Code Check Function 306
- Pin Name I/O 307
- Description 307
- M16C/6N Group (M16C/6NK) 308
- (Flash memory version) 308
- M16C/6N Group (M16C/6NM) 309
- 21.5 Parallel I/O Mode 311
- 21.6 CAN I/O Mode 312
- 21.6.1 ID Code Check Function 312
- _____________ 316
- (ripple) 318
- P-P(ripple) 318
- VCC = 5V 319
- Gain error 321
- Interrupt for 322
- (a) Stop mode release 322
- or 322
- (b) Wait mode release 322
- VCC = 5 V 323
- VCC = 3.3 V 337
- 23. Usage Notes 362
- 23.3 External Clock 364
- 23.5 Power Control 366
- A/D converter 367
- D/A converter 367
- 23.7 Protection 369
- 23.8 Interrupts 370
- 23.8.1 Reading Address 00000h 370
- 23.8.2 Setting SP 370
- 23.8.3 NMI Interrupt 370
- 23.8.5 INT Interrupt 371
- 23.9 DMAC 373
- 23.10 Timers 374
- 23.10.1 Timer A 374
- 23.10.2 Timer B 378
- 23.12 Serial Interface 381
- 23.12.2 Special Modes 382
- 23.12.3 SI/Oi (i = 3 to 6) 383
- 23.13 A/D Converter 384
- 23.14 CAN Module 386
- 23.15 Programmable I/O Ports 391
- 23.16 Dedicated Input Pin 392
- Version MCUs 393
- 23.19.10 Interrupts 396
- 23.19.11 How to Access 396
- 23.19.13 DMA Transfer 396
- 23.21 Noise 398
- Register Index 401
- REVISION HISTORY 403
- Rev.2.10 Apr 14, 2006 411
- Renesas Technology Corp 411
Manuais e produtos relacionados com Redes Renesas M16C/6NK
Redes Renesas 740 Family Manual do Utilizador
(195 páginas)
(195 páginas)
Redes Renesas RJJ10J1643-0101 Manual do Utilizador
(22 páginas)
(22 páginas)
Redes Renesas M16C/30P Manual do Utilizador
(59 páginas)
(59 páginas)
Redes Renesas H8S/2378F Manual do Utilizador
(78 páginas)
(78 páginas)
Redes Renesas TM V.3.20A Manual do Utilizador
(2 páginas)
(2 páginas)
Redes Renesas M3062PT2-EPB Manual do Utilizador
(104 páginas)
(104 páginas)
Redes Renesas M16C/64 Ficha Técnica
(92 páginas)
(92 páginas)
Redes Renesas 740 Family Manual do Utilizador
(124 páginas)
(124 páginas)
Redes Renesas H8S/2378F Informações Técnicas
(109 páginas)
(109 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.067 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais